Angular dependent terahertz emission from the interplay between nanocrystal diamond film and plasmonic metasurface.

Composite structures integrated with metasurfaces and nonlinear films have emerged as alternative candidates to enhance nonlinear response. The cooperative interaction between the two components is complicated. Herein, a split-ring resonator (SRR)-type metasurface was fabricated on a free-standing nanocrystal diamond (NCD) film utilizing electron beam lithography, electron beam evaporation, and a lift-off process. The terahertz (THz) radiation from the SRR-NCD under normal incidence originates from the high-order magnetic resonance of SRR because the NCD film cannot produce detectable THz radiation at this incident angle. As increasing the incident angle, the contribution of the THz radiation from the NCD film gradually increases until reaching 40° incident angle limitation. The results indicate that this angular-dependent THz radiation is induced by the interplay between the NCD film and SRR. This study offers a new approach to investigate nonlinear processes in composite structures.

Intervalley Scattering Induced Terahertz Field Enhancement in Graphene Metasurface.

Terahertz (THz) field enhancement has significant applications in high-resolution imaging, next-generation wireless communications, and networking. In this work, we experimentally demonstrate a graphene metasurface for THz field enhancement that is based on the intervalley scattering theory. Each meta-atom of the metasurface is composed of one split-ring resonator (SRR) embedded in one graphene patch. The experimental results show that, by electrically adjusting the conductivity of the graphene patch, the THz field through the entire sample is enhanced by 23 times and the transmission amplitude at 0.47 THz decreases 8.4 dB. Moreover, the maximum phase difference at 0.43 THz reaches 88°. The experiment shows good agreement with simulation. This study paves a way for exploring THz-matter interactions and nonlinear optics.

Ideal suppression of Bessel beam intensity oscillations with a vortex phase plate.

We propose what we believe to be a new kind of diffractive phase element, i.e., vortex phase plate (VPP) with phase singularities along the azimuth direction. Phase function of the proposed VPP is given analytically. Axial intensity oscillations of propagating Bessel beams are ideally suppressed by using the proposed VPP. Compared with the traditional amplitude mask, the proposed VPP takes such advantages as a simpler fabrication procedure and a lower cost.

Tunable slow light device based on a graphene metasurface.

Slow light devices have significant applications in memory, switching, and quantum optics. However, the design and fabrication of slow light devices with large tunable group delay are still challenging. Here, a graphene-based slow light device that can electrically modulate the group delay of terahertz (THz) waves is proposed and experimentally demonstrated. The unit cell of the device consists of a U-shaped metal resonator and an Ω-shaped metal resonator, with three graphene ribbons embedded between the two resonators. Under electrical stimuli, a relatively high amplitude modulation depth of 74% is achieved and the maximum transmission amplitude is as high as 0.7 at the transmission peak of 0.6 THz. Most importantly, the maximum group delay variation reaches 5 ps at 0.76 THz and the maximum group delay amplitude is as high as 8.8 ps. The experiment shows good agreement with simulation. This study paves a new way for developing novel switchable nanophotonic devices and slow light devices.

A universal route to efficient non-linear response via Thomson scattering in linear solids.

Non-linear materials are cornerstones of modern optics and electronics. Strong dependence on the intrinsic properties of particular materials, however, inhibits the at-will extension of demanding non-linear effects, especially those second-order ones, to widely adopted centrosymmetric materials (for example, silicon) and technologically important burgeoning spectral domains (for example, terahertz frequencies). Here we introduce a universal route to efficient non-linear responses enabled by exciting non-linear Thomson scattering, a fundamental process in electrodynamics that was known to occur only in relativistic electrons in metamaterial composed of linear materials. Such a mechanism modulates the trajectory of charges, either intrinsically or extrinsically provided in solids, at twice the driving frequency, allowing second-harmonic generation at terahertz frequencies on crystalline silicon with extremely large non-linear susceptibility in our proof-of-concept experiments. By offering a substantially material- and frequency-independent platform, our approach opens new possibilities in the fields of on-demand non-linear optics, terahertz sources, strong field light-solid interactions and integrated photonic circuits.

Electromechanically reconfigurable optical nano-kirigami.

Kirigami, with facile and automated fashion of three-dimensional (3D) transformations, offers an unconventional approach for realizing cutting-edge optical nano-electromechanical systems. Here, we demonstrate an on-chip and electromechanically reconfigurable nano-kirigami with optical functionalities. The nano-electromechanical system is built on an Au/SiO2/Si substrate and operated via attractive electrostatic forces between the top gold nanostructure and bottom silicon substrate. Large-range nano-kirigami like 3D deformations are clearly observed and reversibly engineered, with scalable pitch size down to 0.975 µm. Broadband nonresonant and narrowband resonant optical reconfigurations are achieved at visible and near-infrared wavelengths, respectively, with a high modulation contrast up to 494%. On-chip modulation of optical helicity is further demonstrated in submicron nano-kirigami at near-infrared wavelengths. Such small-size and high-contrast reconfigurable optical nano-kirigami provides advanced methodologies and platforms for versatile on-chip manipulation of light at nanoscale.

Single-pixel imaging with neutrons.

Neutron imaging is an invaluable tool for noninvasive analysis in many fields. However, neutron facilities are expensive and inconvenient to access, while portable sources are not strong enough to form even a static image within an acceptable time frame using traditional neutron imaging. Here we demonstrate a new scheme for single-pixel neutron imaging of real objects, with spatial and spectral resolutions of 100 µm and 0.4% at 1 Å, respectively. Low illumination down to 1000 neutron counts per frame pattern was achieved. The experimental setup is simple, inexpensive, and especially suitable for low intensity portable sources, which should greatly benefit applications in biology, material science, and industry.

Artificial modulation of cell width significantly affects the division time of Escherichia coli.

Bacterial cells have characteristic spatial and temporal scales. For instance, Escherichia coli, the typical rod-shaped bacteria, always maintains a relatively constant cell width and cell division time. However, whether the external physical perturbation of cell width has an impact on cell division time remains largely unexplored. In this work, we developed two microchannel chips, namely straight channels and 'necked' channels, to precisely regulate the width of E. coli cells and to investigate the correlation between cell width and division time of the cells. Our results show that, in the straight channels, the wide cells divide much slower than narrow cells. In the 'necked' channels, the cell division is remarkably promoted compared to that in straight channels with the same width. Besides, fluorescence time-lapse microscopy imaging of FtsZ dynamics shows that the cell pre-constriction time is more sensitive to cell width perturbation than cell constriction time. Finally, we revealed a significant anticorrelation between the death rate and the division rate of cell populations with different widths. Our work provides new insights into the correlation between the geometrical property and division time of E. coli cells and sheds new light on the future study of spatial-temporal correlation in cell physiology.

Characterization of a Microscale Superlubric Graphite Interface.

Direct characterizations of the two component surfaces of a solid-solid interface are essential for understanding its various interfacial mechanical, physical, and electrical behaviors. Particularly, the fascinating phenomenon termed structural superlubricity, a state of nearly zero friction and wear, is sensitively dependent on the interface structure. Here we report a controllable pick-and-flip technique to separate a microscale contact pair for the characterization of its two component surfaces for van der Waals layered materials. With this technique, the interface of a graphite superlubric contact is characterized with resolution from microscale down to the atomic level. Imaging of the graphite lattice provides direct proof that this superlubric interface consists of two monocrystalline surfaces incommensurate with each other. More importantly, the structure-property relationship for this contact is investigated. Friction measurements combined with fully atomistic molecular dynamics reveal that internal structures [internals steps, pits, and bulges buried underneath the topmost graphene sheet(s)] have negligible contribution to the total friction; in contrast, external defects lead to a high friction. These results help us to better understand the structure of highly oriented pyrolytic graphite and the fundamental mechanisms of structural superlubricity, as well as to guide the design of superlubricity-based devices.

Direct Experimental Evidence of Biomimetic Surfaces with Chemical Modifications Interfering with Adhesive Protein Adsorption.

Current approaches to dealing with the worldwide problem of marine biofouling are to impart chemical functionality to the surface or utilize microtopography inspired by nature. Previous reports have shown that only introducing a single method may not resist adhesion of mussels or inhibit biofouling in static forms. While it is promising to integrate two methods to develop an effective antifouling strategy, related basic research is still lacking. Here, we have fabricated engineered shark skin surfaces with different feature heights and terminated with different chemical moieties. Atomic force microscopy (AFM) with a modified colloid probe technique and quartz crystal microbalance with a dissipation n (QCM-D) monitoring method have been introduced to directly determine the interactions between adhesive proteins and functionalized surfaces. Our results indicate that the adhesion strength of probe-surface decreases with increasing feature height, and it also decreases from bare Si surface to alkyl and hydroxyl modification, which is attributed to different contact area domains and interaction mechanisms. Combining biomimetic microtopography and surface chemistry, our study provides a new perspective for designing and developing underwater anti-fouling materials.

Nanocracking and metallization doubly defined large-scale 3D plasmonic sub-10 nm-gap arrays as extremely sensitive SERS substrates.

Considering the technological difficulties in the existing approaches to form nanoscale gaps, a convenient method to fabricate three-dimensional (3D) sub-10 nm Ag/SiNx gap arrays has been demonstrated in this study, controlled by a combination of stress-induced nanocracking of a SiNx nanobridge and Ag nanofilm deposition. This scalable 3D plasmonic nanogap is specially suspended above a substrate, having a tunable nanogap width and large height-to-width ratio to form a nanocavity underneath. As a surface-enhanced Raman scattering (SERS) substrate, the 3D Ag/SiNx nanogap shows a large Raman enhancement factor of ∼108 and extremely high sensitivity for the detection of Rhodamine 6G (R6G) molecules, even down to 10-16 M, indicating an extraordinary capability for single-molecule detection. Further, we verified that the Fabry-Perot resonance occurred in the deep SiNx nanocavity under the Ag nanogap and contributed prominently to a tremendous enhancement of the local field in the Ag-nanogap zone and hence ultrasensitive SERS detection. This method circumvents the technological limitations to fabricate a sub-10 nm metal nanogap with unique features for wide applications in important scientific and technological areas.

Side-by-side observation of the interfacial improvement of vertical graphene-coated silicon nanocone anodes for lithium-ion batteries by patterning technology.

We report that vertical graphene coating can greatly improve the electrochemical performance and the interfacial stability of silicon nanocone (SNC) anodes for lithium-ion batteries. The coating patterning technology is innovatively employed for side-by-side demonstration of the exclusive influences of graphene coating on the solid-electrolyte interphase (SEI) formation and the structural stability of the SNC electrode. The silicon nanocone-graphene (SNC-G) electrode achieves a longer cycle life (1715 cycles), higher Coulombic efficiency (average 98.2%), better rate capability, and lower electrode polarization than the SNC electrode. The patterning of the graphene coating provides a much direct and convincing morphological comparison between the SNC-G structure and the SNC structure, showing clearly that the SNC-G area maintains a thin SEI layer and stable nanostructure after cycling, while the SNC area is gradually damaged and covered with a thick SEI layer after 100 cycles. Our results clearly indicate the improved electrochemical performance and interfacial stability attributed to the vertical graphene coating, and the as-proposed patterning technology also paves a new way for comparative research on coating materials for lithium-ion batteries.

A Well-Defined Silicon Nanocone-Carbon Structure for Demonstrating Exclusive Influences of Carbon Coating on Silicon Anode of Lithium-Ion Batteries.

Nanotechnology and carbon coating have been applied to silicon anodes to achieve excellent lithium-ion batteries, but the exclusive influence of carbon coating on solid-electrolyte interphase (SEI) formation is difficult to exhibit distinctly because of the impurity and morphological irregularity of most nanostructured anodes. Here, we design a silicon nanocone-carbon (SNC-C) composite structure as a model anode to demonstrate the significant influences of carbon coating on SEI formation and electrochemical performance, unaffectedly as a result of pure electrode component and distinctly due to regular nanocone morphology. As demonstrated by morphological and elemental analysis, compared to the SNC electrode, the SNC-C electrode maintains a thinner SEI layer (∼10 nm) and more stable structure during cycling as well as longer cycle life (>725 cycles), higher Coulombic efficiency (>99%), and lower electrode polarization. This well-defined structure clearly shows the interface stability attributed to carbon coating and is promising in fundamental research of the silicon anode.

Wavelength de-multiplexing metasurface hologram.

A wavelength de-multiplexing metasurface hologram composed of subwavelength metallic antennas is designed and demonstrated experimentally in the terahertz (THz) regime. Different character patterns are generated at the separated working frequencies 0.50 THz and 0.63 THz which determine a narrow frequency bandwidth of 130 GHz. The two working frequencies are around the central resonance frequency of the antennas where antennas behave strong wavefront modulation. Each antenna is fully utilized to control the wavefront of the metasurface at different frequencies by an optimization algorithm. The results demonstrate a candidate way to design multi-colors optical display elements.

Three Dimensional Hybrids of Vertical Graphene-nanosheet Sandwiched by Ag-nanoparticles for Enhanced Surface Selectively Catalytic Reactions.

Three dimensional (3D) plasmonic nanostructure is perfect for the surface-enhanced Raman scattering (SERS) and also very suitable for surface catalytic reaction, but how to design and fabricate is still a robust task. Here, we show a 3D plasmonic nanohybrid of vertical graphene-nanosheet sandwiched by Ag-nanoparticles on the silicon nanocone array substrate for enhanced surface catalytic reaction. By SERS detection, we find that this hierarchical nanohybrid structure is highly efficient in the enhancement of catalytic reaction, even at a very low concentration of 10(-11) M, which is far better than previous reports by four orders of magnitude. A strong electric field enhancement produced in the 3D framework nanohybrids of graphene nanosheet/Ag-nanoparticles is responsible for this great enhancement of catalytic reaction, due to larger electron collective oscillation in the composite system. Especially the oxygen adsorbed on the graphene and Ag nanoparticles can be excited to triplet excited states, and the electrons on the graphene and the nanoparticles can be effectively transferred to the oxygen, which plays very important role in molecular catalytic reactions. Our results demonstrate the contribution of graphene in plasmon-driven catalytic reactions, revealing a co-driven reaction process.This excellent SERS substrate can be used for future plasmon and graphene co-catalytic surface catalytic reactions, graphene-based surface plasmon sensors and so on.

Morphology modulating the wettability of a diamond film.

Control of the wetting property of diamond surface has been a challenge because of its maximal hardness and good chemical inertness. In this work, the micro/nanoarray structures etched into diamond film surfaces by a maskless plasma method are shown to fix a surface's wettability characteristics, and this means that the change in morphology is able to modulate the wettability of a diamond film from weakly hydrophilic to either superhydrophilic or superhydrophobic. It can be seen that the etched diamond surface with a mushroom-shaped array is superhydrophobic following the Cassie mode, whereas the etched surface with nanocone arrays is superhydrophilic in accordance with the hemiwicking mechnism. In addition, the difference in cone densities of superhydrophilic nanocone surfaces has a significant effect on water spreading, which is mainly derived from different driving forces. This low-cost and convenient means of altering the wetting properties of diamond surfaces can be further applied to underlying wetting phenomena and expand the applications of diamond in various fields.

Wafer-scale double-layer stacked Au/Al2O3@Au nanosphere structure with tunable nanospacing for surface-enhanced Raman scattering.

Fabricating perfect plasmonic nanostructures has been a major challenge in surface enhanced Raman scattering (SERS) research. Here, a double-layer stacked Au/Al2O3@Au nanosphere structures is designed on the silicon wafer to bring high density, high intensity "hot spots" effect. A simply reproducible high-throughput approach is shown to fabricate feasibly this plasmonic nanostructures by rapid thermal annealing (RTA) and atomic layer deposition process (ALD). The double-layer stacked Au nanospheres construct a three-dimensional plasmonic nanostructure with tunable nanospacing and high-density nanojunctions between adjacent Au nanospheres by ultrathin Al2O3 isolation layer, producing highly strong plasmonic coupling so that the electromagnetic near-field is greatly enhanced to obtain a highly uniform increase of SERS with an enhancement factor (EF) of over 10(7). Both heterogeneous nanosphere group (Au/Al2O@Ag) and pyramid-shaped arrays structure substrate can help to increase the SERS signals further, with a EF of nearly 10(9). These wafer-scale, high density homo/hetero-metal-nanosphere arrays with tunable nanojunction between adjacent shell-isolated nanospheres have significant implications for ultrasensitive Raman detection, molecular electronics, and nanophotonics.

Prospects application of polypyrrole-based immunosensor to Porphyromonas gingivalis quantification in subgingival plaque samples.

BACKGROUND: Periodontitis still poses a serious threat to oral and systemic health condition of humans. The proportion of the main pathogenic bacteria change in localized sites was associated with the initiation of the disease process. However, the limitations of microbiological diagnostic aids rendered the diagnosis of active periodontitis status point-of-care or chair-side based on microbiological data difficult. METHODS: Porphyromonas gingivalis, a major putative etiological agent in the initiation and progression of chronic periodontitis, was used as the experimental subject. An immunosensor based on polypyrrole-coated interdigitated array microelectrodes was developed to quantify Porphyromonas gingivalis in pure culture, gingival crevicular fluid and saliva samples. The regression equation for the normalized impedance change (NIC) versus Porphyromonas gingivalis concentration (C) was measured. The correlation between results of the immunosensor and quantitative real-time PCR method in quantifying Porphyromonas gingivalis in subgingival plaque samples was evaluated. RESULTS: Results of the study revealed that the lowest detection limits of the immunosensor was 1.9 x 10(4), 2.7 x 10(5), and 2.7 x 10(6) cells/mL in pure culture, gingival crevicular fluid, and saliva samples respectively. The values determined using the immunosensor strongly correlated with those obtained using quantitative real-time PCR method (R2 = 0.91, p < 0.05). The immunosensor did not require any labels and amplification steps, and the total detection time from sampling to measurement was less than one hour. CONCLUSIONS: The immunosensor developed in the present study offered some insight into monitoring the change in the number of periodontal bacteria chair-side during routine clinical practice.

Sensing self-assembled alkanethiols by differential transmission interrogation with terahertz metamaterials.

Surface-enhanced electromagnetic response in the resonant regions of split-ring resonators offers a sensitive way to probe the surface dipoles formed by alkanethiol molecules with a terahertz wave by a differential transmission (DT) interrogation method. The DT signal mainly comes from the interaction between alkanethiols and metamaterials by electron transfer and/or the variation of the dielectric constant. The Lorentz model is used to demonstrate the principle of DT interrogation theoretically, which suggests the variation of both frequency and damping of resonance can be captured cooperatively. This method has been employed to experimentally demonstrate the sensing feasibility for the chain length dependence of the alkanethiol molecules. Numerical simulations confirm that the enhancement is large at the gap and corner regions of this kind of metamaterials.